TECHNICAL SUPPORT
Published 2026-03-31
Cher Wing MicroservoGuide to
and cost for you
withservothat and size? Many face and when micro into space- . The Cher Wing microservothese pain with a on high power . This guide you a data- of its and . You will learn how to costs . We a clear to your using the Cher Wing .
The key such as width, gear train, and . We will these to ROI . By the end of this , you will how to apply the Cher Wing micro servo in and light . Let us dive into the that to your line.
how much force a motor can to its . The Cher Wing micro servo a rated of 2.5 kg-cm while only 9 grams. This gives it a -to- ratio of 0.278 kg-cm per gram, which is 18% than micro in the same price range. The lies in its 12-pole rotor, which flux .
Field tests show that this high into times for . In a pick-and-place cycle 0.8 , the Cher Wing micro servo with less than 3% . note that this a range of 4.8V to 6.0V. For , this means you can your power unit, $12 per .
gear wear down under loads, to every 10,000 . The Cher Wing micro servo a steel gear train with -cut teeth that a of HRC 55. lab tests zero wear after 50,000 at 60- . This cuts your by 40% to brass- .
The gear train also a that shock loads from the motor shaft. When an stall , the the , the servo to after . Field data from shows this mean time to over 18 . For three , this to 720 hours of saved .
to the range of input pulse where the servo does not , lag. The Cher Wing micro servo an ultra- of 1.5 , which is 50% than the of 3 . This the servo to its 2,000 times per when with a . In CNC tests, this to just 0.02 over a 100- .
also when work in . For a four-axis arm, the Cher Wing micro servo less than 0.5- axes. teams this it the need for. By the servo loop, you can -loop at open-loop costs.
Heat is the cause of in micro , over time. The Cher Wing micro servo an alloy shell that acts as a heat sink, case by 12°C to fully. shows the motor peaks at 78°C under stall, well below the 100°C. This the servo to run at full load for 30.
heat is by slots in the case, which . In high-duty-cycle like delta 120 items per , this below 85°C. pair the Cher Wing micro servo with a PWM set to 16 kHz to eddy . This a life 10,000 hours, by life .
and . The Cher Wing micro servo 1520μs pulse and at 330Hz rate, most PLC . Its 25-tooth fits all servo arms, while the 3-pin JR plug-and-play with . A at an line 45 with Cher Wing units a line of PLC code.
For , the servo pulse from 800μs to 2200μs, 180- . This of while . The servo for major PLC like and . By these XML files, setup time drops from two hours to per axis. note that the Cher Wing micro servo is RoHS , in .
for the Cher Wing micro servo start at 500 units, where the per-unit price drops by 22% to -unit . A mid-sized 2,000 units saves $4,800, to fund an week for . The when in , as the servo's 0.5% rate is half the . For large OEMs, a 12-month can an 5% based on .
costs, the Cher Wing micro servo like costs. Its and mean you can stock one SKU for types. A case study from a that on this servo their spare parts value by $15,000 . , the , $0.20 per unit on air from Asia. These make a case for to .
This bar chart the Cher Wing micro servo three based on -to- ratio. The axis kg-cm per gram, from 0 to 0.3. A 0.21, B 0.19, C 0.22, while Cher Wing 0.278. The chart that Cher Wing the rival by 26%, it the for - arms.
This line graph case rise over a 20- test at 0.5- . The axis shows time in , while the axis shows in . Cher Wing micro servo at 52°C after 8 , to 68°C. The after the 5- mark, the of the heat sink. This data the claim that Cher Wing can in up to 50°C.
This chart total costs for a 100-servo . Cost , , ,and . The Cher Wing shows a 34% lower total cost than, due to . The third-year for Cher Wing is 42% than the , long-term . can use this chart to based on .
What is the of the Cher Wing micro servo in
Under with 50% duty cycle and 25°C, the servo 8,000 hours drops below 80% of rated value. This is by wear tests and brush.
Does the servo third-party
Yes, the Cher Wing micro servo works with any 3.3V to 5V PWM. , for , we it with the servo -loop for real-time.
How do I a for
our sales team the to a . your test and load so we can the .
Are there any IP for dusty
The an IP40 . For metal or dust, we offer an that adds IP54 at a 15% price .
What is the MOQ for servo horns
horn an order of 1,000 units. The lead time is 25 days for plus 15 days for . servo free DFM to your CAD file mass .
The Cher Wing micro servo in , , and . Its metal gear train costs while the . We have its over in real-world . For , this means over- your power . For , the long-term costs and spare parts.
Ready to your ? Visit the servo to a free DFM for your . Our team same-day and for bulk . the and 3D CAD model to begin your today. our Asia for 48 hours.
Update Time：2026-03-31
Contact Kpower's product specialist to recommend suitable motor or gearbox for your product.
